Wankel engine

Wikicars, a place to share your automotive knowledge
Jump to: navigation, search

The Wankel engine is a type of internal combustion engine which uses a rotary design to convert pressure into a rotating motion instead of using reciprocating pistons. Its four-stroke cycle takes place in a space between the inside of an oval-like epitrochoid-shaped housing and a rotor that is similar in shape to a Reuleaux triangle. This design delivers smooth high-rpm power, from a compact size. Since its introduction the engine has been commonly referred to as the rotary engine, though this name is also applied to several completely different designs.

The engine was invented by German engineer Felix Wankel. He began its development in the early 1950s at NSU Motorenwerke AG (NSU) before completing a working, running prototype in 1957. NSU then subsequently licenced the concept to other companies across the globe, who have continued to improve the design.

Because of their compact design, Wankel rotary engines have been installed in a variety of vehicles and devices such as automobiles including racing cars, along with aircraft, go-karts, personal water craft, chain saws, and auxiliary power units. The most extensive automotive use of the Wankel engine has been by the Japanese company Mazda.


In 1951, the German engineer Felix Wankel began development of the engine at NSU Motorenwerke AG, where he first conceived his rotary engine in 1954 (DKM 54, Drehkolbenmotor). The so-called KKM 57 (the Wankel rotary engine, Kreiskolbenmotor) was constructed by NSU engineer Hanns Dieter Paschke in 1957 without the knowledge of Felix Wankel, who remarked "you've turned my race horse into a plow mare".<ref>Template:Citation/core{{#if:|}}</ref> The first working prototype DKM 54 was running on February 1, 1957 at the NSU research and development department Versuchsabteilung TX.<ref>Template:Citation/core{{#if:|}}</ref>

Considerable effort went into designing rotary engines in the 1950s and 1960s. They were of particular interest because they were smooth and quiet running, and because of the reliability resulting from their simplicity.

In the United States, in 1959 under license from NSU, Curtiss-Wright pioneered minor improvements in the basic engine design. In Britain, in the 1960s, Rolls Royce Motor Car Division at Crewe, Cheshire, pioneered a two-stage diesel version of the Wankel engine.<ref>R1 two stage compound diesel Wankel 1966. Retrieved on September 27, 2008. </ref>

Also in Britain, Norton Motorcycles developed a Wankel rotary engine for motorcycles, which was included in their Commander and F1; Suzuki also made a production motorcycle with a Wankel engine, the RE-5. In 1971 and 1972 Arctic Cat produced snowmobiles powered by 303 cc Wankel rotary engines manufactured by Sachs in Germany. Deere & Company designed a version that was capable of using a variety of fuels. The design was proposed as the power source for United States Marine Corps combat vehicles and other equipment in the late 1980s.<ref>Template:Citation/core{{#if:|}}</ref>

After occasional use in automobiles, for instance by NSU with their Ro 80 model,<ref>"The Wankel Wager", Time, September 08, 1967, retrieved on September 27, 2008.</ref> Citroën with the M35, and GS Birotor using engines produced by Comotor, as well as abortive attempts by General Motors and Mercedes-Benz to design Wankel-engine automobiles, the most extensive automotive use of the Wankel engine has been by the Japanese company Mazda.

After years of development, Mazda's first Wankel engine car was the 1967 Cosmo. The company followed with a number of Wankel ("rotary" in the company's terminology) vehicles, including a bus and a pickup truck. Customers often cited the cars' smoothness of operation. However, Mazda chose a method to comply with hydrocarbon emission standards that, while less expensive to produce, increased fuel consumption, just before a sharp rise in fuel prices. Mazda later abandoned the Wankel in most of their automotive designs, but continued using it in their RX-7 sports car until August 2002 (RX-7 importation for North America ceased with the 1995 model year). The company normally used two-rotor designs, but the 1991 Eunos Cosmo used a twin-turbo three-rotor engine. In 2003, Mazda introduced the Renesis engine with the RX-8. The Renesis engine relocated the ports for exhaust and intake from the periphery of the rotary housing to the sides, allowing for larger overall ports, better airflow, and further power gains. The Renesis is capable of delivering 238 hp (177 kW) with better fuel economy, reliability, and environmental friendliness than previous Mazda rotary engines,<ref>rotary2.pdf Mazda's Rotary Engine for the Next Millennium RENESIS, p. 6-7, 1999. Mazda.</ref> all from its 1.3 L displacement.

In 1961, the Soviet research organization of NATI, NAMI and VNIImotoprom started experimental development, and created experimental engines with different technologies.<ref>Иван Пятов.РПД изнутри и снаружи, Двигатель №5-6 (11-12) сентябрь-декабрь 2000</ref>

Soviet automobile manufacturer AvtoVAZ also experimented with the use of Wankel engines in cars but without the benefit of a license.<ref>Template:Citation/core{{#if:|}}</ref> In 1974 they created a special engine design bureau, which in 1978 designed an engine designated as VAZ-311. In 1980, the company started delivering Wankel-powered VAZ-2106s (VAZ-411 engine with two-rotors) and Ladas, mostly to security services, of which about 200 were made.<ref>"LADA - part II" Autosoviet, undated, retrieved on September 27, 2008.</ref><ref>"ЛИНИЯ ЖИЗНИ - ЭПИТРОХОИДА" 01.07.2001, retrieved on September 27, 2008. (Russian)</ref> The next models were the VAZ-4132 and VAZ-415. Aviadvigatel, the Soviet aircraft engine design bureau, is known to have produced Wankel engines with electronic injection for aircraft and helicopters, though little specific information has surfaced.

Although many manufacturers licensed the design, and Mercedes-Benz used it for their C111 concept car, only Mazda has produced Wankel engines in large numbers. American Motors (AMC) was so convinced "...that the rotary engine will play an important role as a powerplant for cars and trucks of the future...", according to Chairman Roy D. Chapin Jr., that the smallest U.S. automaker signed an agreement in February 1973, after a year's negotiations, to build Wankels for both passenger cars and Jeeps, as well as the right to sell any rotary engines it produces to other companies.<ref>Ward's Auto World Staff, "Rearview mirror", Ward's Auto World, February 1, 2000. Retrieved on: January 25, 2008.</ref><ref>Template:Citation/core{{#if:|}}</ref> It even designed the unique Pacer around the engine, even though by then, AMC had decided to buy the Wankel engines from GM instead of building them itself. However, GM's engines had not reached production when the Pacer was to hit the showrooms. Part of the demise of this feature was the 1973 oil crisis with rising fuel prices, and also concerns about proposed US emission standards legislation. General Motors' Wankel did not comply with those emission standards, so in 1974 the company canceled its development. This meant the Pacer had to be reconfigured to house AMC's venerable AMC Straight-6 engine with rear-wheel drive.


In the Wankel engine, the four strokes of a typical Otto cycle occur in the space between a three-sided symmetric rotor and the inside of a housing. In the basic single-rotor Wankel engine, the oval-like epitrochoid-shaped housing surrounds a rotor which is similar to a Reuleaux triangle, a three-pointed curve of constant width, but with the bulge in the middle of each side a bit more flattened. From a theoretical perspective, the chosen shape of the rotor between the fixed apexes is basically the result of a minimization of the volume of the geometric combustion chamber and a maximization of the compression ratio, respectively. Thus, the symmetric curve connecting two arbitrary apexes of the rotor is maximized in the direction of the inner housing shape with the constraint not to touch the housing at any angle of rotation (an arc is not a solution of this optimization problem).

The central drive shaft, called the eccentric shaft or E-shaft, passes through the center of the rotor and is supported by fixed bearings. The rotors ride on eccentrics (analogous to cranks) integral with the eccentric shaft (analogous to a crankshaft). The rotors both rotate around the eccentrics and make orbital revolutions around the eccentric shaft. Seals at the corners of the rotor seal against the periphery of the housing, dividing it into three moving combustion chambers. The turning of each rotor is caused and controlled by a pair of synchronizing gears. A fixed gear mounted on one side of the rotor housing engages a ring gear attached to the rotor and ensures the rotor moves exactly 1/3 turn for each turn of the eccentric shaft. The power output of the engine is not transmitted through the synchronizing gears. The force of gas pressure on the rotor is (to a first approximation) directed to the center of the eccentric, on the output shaft.

The best way to visualize the action of the engine in the animation at left is to look not at the rotor itself, but the cavity created between it and the housing. The Wankel engine is actually a variable-volume progressing-cavity system. Thus there are 3 cavities per housing, all repeating the same cycle. Note as well that points A and B on the rotor and e-shaft turn at different speed, point B moves 3 times faster than point A, so that one full orbit of the rotor equates to 3 turns of the e-shaft.

As the rotor rotates and orbitally revolves, each side of the rotor gets closer and farther from the wall of the housing, compressing and expanding the combustion chamber similarly to the strokes of a piston in a reciprocating engine. The power vector of the combustion stage goes through the center of the offset lobe.

While a four-stroke piston engine makes one combustion stroke per cylinder for every two rotations of the crankshaft (that is, one half power stroke per crankshaft rotation per cylinder), each combustion chamber in the Wankel generates one combustion stroke per each driveshaft rotation, i.e. one power stroke per rotor orbital revolution and three power strokes per rotor rotation. Thus, power output of a Wankel engine is generally higher than that of a four-stroke piston engine of similar engine displacement in a similar state of tune; and higher than that of a four-stroke piston engine of similar physical dimensions and weight.

Wankel engines also generally have a much higher redline than a reciprocating engine of similar power output, in part because the smoothness inherent in circular motion, but especially because they do not have highly stressed parts such as a crankshaft or connecting rods. Eccentric shafts do not have the stress-raising internal corners of crankshafts. The redline of a rotary engine is limited by wear of the synchronizing gears. Hardened steel gears are used for extended operation above 7000 or 8000 rpm. Mazda Wankel engines in auto racing are operated above 10,000 rpm. In aircraft they are used conservatively, up to 6500 or 7500 rpm.

National agencies that tax automobiles according to displacement and regulatory bodies in automobile racing variously consider the Wankel engine to be equivalent to a four-stroke engine of 1.5 to 2 times the displacement; some racing sanctioning bodies ban it altogether.<ref>FIA Reglement 5 engine: Only 4-Stroke engine with reciprocating piston are permitted, see page 12. Retrieved on: January 25, 2008.</ref>


Felix Wankel managed to overcome most of the problems that made previous rotary engines fail by developing a configuration with vane seals that could be made of more durable materials than piston ring metal that led to the failure of previous rotary designs.<ref>Moller Freedom Motors formerly Outboard Marine Corporation (Evirude/Johnson) Rotary engines Moller Skycar</ref>

Rotary engines have a thermodynamic problem not found in reciprocating four-stroke engines in that their "cylinder block" operates at steady state, with intake, compression, combustion, and exhaust occurring at fixed housing locations for all "cylinders". In contrast, reciprocating engines perform these four strokes in one chamber, so that extremes of "freezing" intake and "flaming" exhaust are averaged and shielded by a boundary layer from overheating working parts.

The boundary layer shields and the oil film act as thermal insulation, leading to a low temperature of the lubricating film (max. ~200 °C/400 °F) on a water-cooled Wankel engine. This gives a more constant surface temperature. The temperature around the spark plug is about the same as the temperature in the combustion chamber of a reciprocating engine. With circumferential or axial flow cooling, the temperature difference remains tolerable.<ref>1971 Rotary Engine Kenichi Yamamoto, Toyo Kogyo LTD p.67 Fig 5.10 and 5.11</ref><ref>1981, Rotary Engine Kenichi Yamamoto, Toyo Kogyo LTD p.32 p.33 Fig3.39 Fig3.40 Fig3.41 </ref><ref>Richard F. Ansdale Der Wankelmotor Motor Buch Verlag p.141-150 </ref><ref>Wolf-Dieter Bensinger Rotationskolben - Verbrennungsmotoren Springer-Verlag Berlin Heidelberg ISBN 3-540-05886-9</ref>

Four-stroke reciprocating engines are less suitable for hydrogen. The hydrogen can misfire on hot parts like the exhaust valve and spark plugs. Another problem concerns the hydrogenate attack on the lubricating film in reciprocating engines. In a Wankel engine this problem is circumvented by using a ceramic apex seal against a ceramic surface: there is no oil film to suffer hydrogenate attack. Since ceramic piston rings are not available as of 2008, the problem remains with the reciprocating engine. The piston shell must be lubricated and cooled with oil. This substantially increases the lubricating oil consumption in a four-stroke hydrogen engine.


Unlike a piston engine, where the cylinder is cooled by the incoming charge after being heated by combustion, Wankel rotor housings are constantly heated on one side and cooled on the other, leading to high local temperatures and unequal thermal expansion. While this places high demands on the materials used, the simplicity of the Wankel makes it easier to use alternative materials like exotic alloys and ceramics. With water cooling in a radial or axial flow direction, with the hot water from the hot bow heating the cold bow, the thermal expansion remains tolerable.<ref>Kenichi Yamamoto Rotary Engine Side 32 cooling system</ref>


Early engine designs had a high incidence of sealing loss, both between the rotor and the housing and also between the various pieces making up the housing. Also, in earlier model Wankel engines carbon particles could become trapped between the seal and the casing, jamming the engine and requiring a partial rebuild. (This can be prevented in older Mazda engines by always allowing the engine to reach operating temperature). It was common for very early Mazda engines to require rebuilding after 50,000 miles (80,000 km). Modern Wankel engines have not had these problems for many years. Further sealing problems arise from the uneven thermal distribution within the housings causing distortion and loss of sealing and compression. This thermal distortion also causes uneven wear between the apex seal and the rotor housing, quite evident on higher mileage engines. Attempts have been made to normalize the temperature of the housings, minimizing the distortion, with different coolant circulation patterns and housing wall thicknesses.

Fuel consumption and emissions

Just as the shape of the Wankel combustion chamber is resistant to preignition and will run on lower-octane gasoline than a comparable piston engine,<ref>The Wankel Rotary Engine, John B. Hege, McFarland & Company, 2002, ISBN 0786411775, ISBN 9780786411771, page 10</ref> it also leads to relatively incomplete combustion of the air-fuel charge, with a larger amount of unburned hydrocarbons released into the exhaust. The exhaust is, however, relatively low in NOx emissions; this allowed Mazda to meet the United States Clean Air Act of 1970 in 1973 with a simple and inexpensive 'thermal reactor' (an enlarged open chamber in the exhaust manifold) by paradoxically enriching the air-fuel ratio to the point where the unburned hydrocarbons in the exhaust would support complete combustion in the thermal reactor; while piston-engine cars required expensive catalytic converters to deal with both unburned hydrocarbons and NOx emissions. This raised fuel consumption, however (already a weak point for the Wankel engine) at the same time that the oil crisis of 1973 raised the price of gasoline. Mazda was able to improve the fuel efficiency of the thermal reactor system by 40% by the time of introduction of the RX-7 in 1978, but eventually shifted to the catalytic converter system.<ref>”Development of Low-Emission Rotary Engines”, Mazda Motor Corporation</ref>

In Mazda's RX-8 with the Renesis engine, fuel consumption is now within normal limits while passing California State emissions requirements. The exhaust ports, which in earlier Mazda rotaries were located in the rotor housings, were moved to the sides of the combustion chamber. This approach allowed Mazda to eliminate overlap between intake and exhaust port openings, while simultaneously increasing exhaust port area. The Renesis engine even meets California's Low Emissions Vehicle or LEV standards.


Wankel engines are considerably simpler, lighter, and contain far fewer moving parts than piston engines of equivalent power output. For instance, because valving is accomplished by simple ports cut into the walls of the rotor housing, they have no valves or complex valve trains; in addition, since the rotor is geared directly to the output shaft, there is no need for connecting rods, a conventional crankshaft, crankshaft balance weights, etc. The elimination of these parts often makes a Wankel engine much lighter and it also completely eliminates the reciprocating mass of a piston engine with its internal strain and inherent vibration due to repeated acceleration and deceleration, producing not only a smoother flow of power but also the ability to produce more power by running at higher rpm.

The surface/volume-ratio problem is so complex that one cannot make a direct comparison between a reciprocating piston engine and a Wankel engine in terms of the surface/volume-ratio. The flow velocity and the heat losses behave quite differently. Surface temperatures behave absolutely differently; the film of oil in the Wankel engine acts as insulation. Engines with a higher compression ratio have a worse surface/volume-ratio. The surface/volume-ratio of a Diesel engine is much worse than a gasoline engine, but Diesel engines are well known for a higher efficiency factor than gasoline engines. Thus, engines with equal power should be compared: a naturally aspirated 1.3 liter Wankel engine with a naturally aspirated 1.3 liter four stroke reciprocating piston engine with equal power. But such a four stroke engine is not possible and needs twice the displacement for the same power as a Wankel engine. The extra or "empty" stroke(s) should not be ignored, as a 4-stroke cylinder produces a power stroke only every other rotation of the crankshaft. In actuality, this doubles the real surface/volume-ratio for the four stroke reciprocating piston engine and the demand of displacement.<ref>ANSDALE, R. F. (1971). Der Wankelmotor Konstruktion u. Wirkungsweise. Stuttgart, Motorbuch-Verlag., p. 73, 91-92, 200, Verhältnis Oberfläche zu Volumen; German</ref><ref>Wolf-Dieter Bensinger: Rotationskolben – Verbrennungsmotoren. Springer-Verlag, Berlin/Heidelberg, ISBN 3-540-05886-9 (Auslegung des Kühlers; construction of a radiator for a Wankel engine) </ref> Higher volumetrically efficiency, lower pumping loss through the absence of choking valves.<ref>ANSDALE, R. F. (1971). Der Wankelmotor Konstruktion u. Wirkungsweise. Stuttgart, Motorbuch-Verlag., p. 121-133; German </ref>

Because of the quasi-overlap of the power strokes that cause the smoothness of the engine, and the avoidance of the 4-stroke cycle in a reciprocating engine, the Wankel engine is very quick to react to throttle changes and is able to quickly deliver a surge of power when the demand arises, especially at higher rpms. This difference is more pronounced when compared to 4 cylinder reciprocating engines and less pronounced when compared to higher cylinder counts.

In addition to the removal of internal reciprocating stresses by virtue of the complete removal of its reciprocating internal parts typically found in a piston engine, the engine is constructed with an iron rotor within a housing made of aluminium, which has a greater coefficient of thermal expansion. This ensures that even a severely overheated Wankel engine cannot seize, as would likely occur in an overheated piston engine. This is a substantial safety benefit in aircraft use since no valves can burn out.

A further advantage of the Wankel engine for use in aircraft is the fact that a Wankel engine can have a smaller frontal area than a piston engine of equivalent power allowing a more aerodynamic nose to be designed around it. The simplicity of design and smaller size of the Wankel engine also allows for savings in construction costs, compared to piston engines of comparable power output.

Of perhaps the most importance is that Wankel engines that operate within their original design parameters are almost immune to catastrophic failure. A Wankel engine that loses compression, cooling or oil pressure will lose a large amount of power, and will die over a short period of time; however, it will usually continue to produce some power during that time. Piston engines under the same circumstances are prone to seizing or breaking parts that almost certainly results in major internal damage of the engine and an instant loss of power. For this reason, Wankel engines are very well suited to aircraft.

Due to a 50% longer stroke duration compared to a four cycle engine, there is more time to complete the combustion. This leads to greater suitability for Direct injection. A Wankel rotary engine has stronger flows of air-fuel mixture and a longer operating cycle than a reciprocating engine, so it realizes concomitantly thorough mixing of hydrogen and air. The result is a homogeneous mixture, which is crucial for hydrogen combustion.<ref>Template:Citation/core{{#if:|}}</ref>


Although in two dimensions the seal system of a Wankel looks to be even simpler than that of a corresponding multi-cylinder piston engine, in three dimensions the opposite is true. As well as the rotor apex seals evident in the conceptual diagram, the rotor must also seal against the chamber ends.

Piston rings are not perfect seals; in fact, each has a gap to allow for expansion. Moreover, the sealing at the Wankel apexes is less critical, as leakage is between adjacent chambers on adjacent strokes of the cycle, rather than to the crankcase. However, the less effective sealing of the Wankel is one factor reducing its efficiency, confining its success mainly to applications such as racing engines and sports vehicles where neither efficiency nor long engine life are major considerations.

Compared to four stroke piston engines, the time available for fuel to be port injected into a Wankel engine is significantly shorter, due to the way the three chambers rotate. The fuel-air mixture cannot be pre-stored as there is no intake valve. Also the Wankel engine, compared to a piston engine, has 50% longer stroke duration. The four Otto cycles last 1080° for a Wankel engine versus 720° for a four stroke reciprocating piston engine.

There are various methods of calculating the engine displacement of a Wankel; the Japanese regulations calculating displacements for engine ratings on the basis of the volume displacement of one rotor face only. This is widely accepted as the standard method of calculating the displacement of a rotary, however comparing a piston engine to a Wankel rotary using this displacement convention is flawed and results in large imbalances in specific output in favor of the Wankel motor. Many believe this is for marketing purposes on Mazda's part.

For comparison purposes between a Wankel Rotary engine and a piston engine, displacement (and thus power output) can more accurately be compared on a displacement per revolution (of the eccentric shaft) basis. This dictates that a two rotor Wankel displacing 654 cc per face will have a displacement of 1.3 liters per every rotation of the eccentric shaft(only two total faces, one face per rotor going through a full power stroke) and 2.6 liters after two revolutions (four total faces, two faces per rotor going through a full power stroke). This is directly comparable to a 2.6-liter piston engine with an even number of cylinders in a conventional firing order which will also displace 1.3 liters through its power stroke after one revolution of the crankshaft, and 2.6 liters through its power strokes after two revolutions of the crankshaft. However, a Wankel Rotary engine is still a 4-stroke engine and pumping losses from non-power strokes still apply. But the absence of throttling valves and a 50% longer stroke duration result in a significantly lower pumping loss compared against a four stroke reciprocating piston engine. Measuring a Wankel rotary engine in this way more accurately explains its specific output numbers, as the volume of its air fuel mixture put through a complete power stroke per revolution is directly responsible for torque and thus horsepower produced.

The trailing side of the rotary engine's combustion chamber develops a squeeze stream which pushes back the flamefront. With the conventional two-spark-plug or one-spark-plug system and homogenous mixture, this squeeze stream prevents the flame from propagating to the combustion chamber's trailing side in the mid and high engine speed ranges. This is why there can be more carbon monoxide and unburnt hydrocarbons in a Wankel's exhaust stream. A side port exhaust, as is used in the Renesis avoids this because the unburned mixture cannot escape. The Mazda 26B avoided this issue through a 3-spark plug ignition system. (As a result, at the Le Mans 24 hour endurance race in 1991, the 26B had significantly lower fuel consumption than the competing reciprocating piston engines. All competitors had only the same amount of fuel available, because of the Le Mans 24h limited fuel quantity rule.<ref>SAE Paper 920309 Mazda 26B 4-Rotor Rotary Engine for Le Mans Page 7, 3-Plug Ignitions System</ref>)

All Mazda-made Wankel rotaries, including the new Renesis found in the RX8, burn a small quantity of oil by design; it is metered into the combustion chamber in order to preserve the apex seals. Owners must periodically add small amounts of oil, marginally increasing running costs—though it is still reasonable and comparable in some instances when compared to many reciprocating piston engines.


Automobile racing

In the racing world, Mazda has had substantial success with two-rotor, three-rotor, and four-rotor cars. Private racers have also had considerable success with stock and modified Mazda Wankel-engine cars.<ref>Template:Citation/core{{#if:|}}</ref>

The Sigma MC74 powered by a Mazda 12A engine was the first engine and team from outside Western Europe or the United States to finish the entire 24 hours of the 24 Hours of Le Mans race, in 1974. Mazda is the only team from outside Western Europe or the United States to have won Le Mans outright and the only non-piston engine ever to win Le Mans, which the company accomplished in 1991 with their four-rotor 787B (2,622 cc/160 cu in — actual displacement, rated by FIA formula at 4,708 cc/287 cu in). The following year, a planned rule change at Le Mans made the Mazda 787B ineligible to race anymore due to weight advantages. Mazda is also the most reliable finisher at Le Mans (with the exception of Honda, who has entered only three cars in only one year), with 67% of entries finishing.

The Mazda RX-7 has won more IMSA races in its class than any other model of automobile, with its one hundredth victory on September 2, 1990. Following that, the RX-7 won its class in the IMSA 24 Hours of Daytona race ten years in a row, starting in 1982. The RX7 won the IMSA Grand Touring Under Two Liter (GTU) championship each year from 1980 through 1987, inclusive.

Formula Mazda Racing features open-wheel race cars with Mazda Wankel engines, adaptable to both oval tracks and road courses, on several levels of competition. Since 1991, the professionally organized Star Mazda Series has been the most popular format for sponsors, spectators, and upward bound drivers. The engines are all built by one engine builder, certified to produce the prescribed power, and sealed to discourage tampering. They are in a relatively mild state of racing tune, so that they are extremely reliable and can go years between motor rebuilds.<ref name = "star">Template:Citation/core{{#if:|}}</ref>

The Malibu Grand Prix chain, similar in concept to commercial recreational kart racing tracks, operates several venues in the United States where a customer can purchase several laps around a track in a vehicle very similar to open wheel racing vehicles, but powered by a small Curtiss-Wright rotary engine.

In engines having more than two rotors, or two rotor race engines intended for high-rpm use, a multi-piece eccentric shaft may be used, allowing additional bearings between rotors. While this approach does increase the complexity of the eccentric shaft design, it has been used successfully in the Mazda's production three-rotor 20B-REW engine, as well as many low volume production race engines. (The C-111-2 4 Rotor Mercedes-Benz eccentric shaft for the KE Serie 70, Typ DB M950 KE409 is made in one piece! Mercedes-Benz used split bearings.)

Other uses

Small Wankel engines are being found increasingly in other roles, such as go-karts,<ref>Template:Citation/core{{#if:|}}</ref><ref>Template:Citation/core{{#if:|}}</ref> personal water craft and auxiliary power units for aircraft.<ref>Template:Citation/core{{#if:|}}</ref><ref>Template:Citation/core{{#if:|}}</ref> The Graupner/O.S. 49-PI is a 1.27 hp (947 W) 5 cc Wankel engine for model airplane use which has been in production essentially unchanged since 1970; even with a large muffler, the entire package weighs only 380 grams (13.4 ounces).<ref>Template:Citation/core{{#if:|}}</ref><ref>Template:Citation/core{{#if:|}}</ref>

The simplicity of the Wankel makes it well-suited for mini, micro, and micro-mini engine designs. The Microelectromechanical systems (MEMS) Rotary Engine Lab at the University of California, Berkeley has been developing Wankel engines of down to 1 mm in diameter with displacements less than 0.1 cc. Materials include silicon and motive power includes compressed air. The goal is to eventually develop an internal combustion engine that will deliver 100 milliwatts of electrical power; the engine itself will serve as the rotor of the generator, with magnets built into the engine rotor itself.<ref>Template:Citation/core{{#if:|}}</ref><ref>Berkley-MEMS-Wankel engine</ref>

The largest Wankel engine was built by Ingersoll-Rand; available in 550 hp (410 kW) one rotor and 1100 hp (820 kW) two rotor versions, displacing 41 liters per rotor with a rotor approximately one meter in diameter, it was available between 1975 and 1985. It was derived from a previous, unsuccessful Curtiss-Wright design, which failed because of a well-known problem with all internal combustion engines: the fixed speed at which the flame front travels limits the distance combustion can travel from the point of ignition in a given time, and thereby limiting the maximum size of the cylinder or rotor chamber which can be used. This problem was solved by limiting the engine speed to only 1200 rpm and the use of natural gas as fuel; this was particularly well chosen, as one of the major uses of the engine was to drive compressors on natural gas pipelines.<ref>Template:Citation/core{{#if:|}}</ref>

Non-internal combustion

Aside from being used for internal combustion engines, the basic Wankel design has also been utilized for gas compressors, and superchargers for internal combustion engines, but in these cases, although the design still offers advantages in reliability, the basic advantages of the Wankel in size and weight over the four-stroke internal combustion engine are irrelevant. In a design using a Wankel supercharger on a Wankel engine, the supercharger is twice the size of the engine.

Perhaps the most exotic use of the Wankel design is in the seat belt pre-tensioner system<ref>Template:Citation/core{{#if:|}}</ref> of some Mercedes-Benz<ref>Template:Citation/core{{#if:|}}</ref> and Volkswagen<ref>Template:Citation/core{{#if:|}}</ref> cars. In these cars, when deceleration sensors sense a potential crash, small explosive cartridges are triggered electrically and the resulting pressurized gas feeds into tiny Wankel engines which rotate to take up the slack in the seat belt systems, anchoring the driver and passengers firmly in the seat before a collision.<ref>Template:Citation/core{{#if:|}}</ref>

See also

Piston engine configurations
v  d  e
Type BourkeTemplate:· Controlled combustionTemplate:· DelticTemplate:·OrbitalTemplate:· PistonTemplate:· Pistonless (Wankel)Template:· RadialTemplate:· RotaryTemplate:· SingleTemplate:· Split cycleTemplate:· StelzerTemplate:· Tschudi
Inline types H · U · Square four · VR · Opposed · X
Stroke cycles Two-stroke cycleTemplate:· Four-stroke cycleTemplate:· Six-stroke cycle
Straight Single · 2 · 3 · 4 · 5 · 6 · 8 · 10 · 12 · 14
Flat 2 · 4 · 6 · 8 · 10 · 12 · 16
V 4 · 5 · 6 · 8 · 10 · 12 · 16 · 20 · 24
W 8 · 12 · 16 · 18
Valves Cylinder head portingTemplate:· CorlissTemplate:· SlideTemplate:· ManifoldTemplate:· MultiTemplate:· PistonTemplate:· PoppetTemplate:· SleeveTemplate:· Rotary valveTemplate:· Variable valve timingTemplate:· Camless
Mechanisms CamTemplate:· Connecting rodTemplate:· CrankTemplate:· Crank substituteTemplate:· CrankshaftTemplate:· Scotch YokeTemplate:· SwashplateTemplate:· Rhombic drive
Linkages EvansTemplate:· Peaucellier–LipkinTemplate:· Sector straight-lineTemplate:· Watt's (parallel)
Other HemiTemplate:· RecuperatorTemplate:· Turbo-compounding

External links

Wikimedia Commons has media related to: