.
GM Iron Duke engine
| place image here in 300 pixels | |
| GM Iron Duke | |
|---|---|
| Engine | |
| Manufacturer | Pontiac |
| aka | Crossflow (low) Tech IV |
| Type | Petrol |
| Production/Introduction | 1977 - 1993 |
| Status | Discontinued |
| Displacement | 3.5 litre (150.8 cu in) |
| Aspiration | write its type of aspiration |
| Configuration | Inline (Straight) |
| Cylinders | Four (4) |
| Fuel System | Carburated (1977-1981) TBI fuel injection (1982-1993, TechIV) |
| Lubrification | indicate the engine's type of lubrification |
| Output | 1977 85 hp (63 kW) @ N/A rpm 123 lb-ft. (167 Nm) of torque @ N/A rpm 1979 90 hp (67 kW) @ N/A rpm 128 lb-ft. (173 Nm) of torque @ N/A rpm 1980 86 hp (64 kW) @ N/A rpm 128 lb-ft. (173 Nm) of torque @ N/A rpm 1987 98 hp (73 kW) @ N/A rpm N/A lb-ft. of torque @ N/A rpm 1989 110 hp (82 kW) @ N/A rpm N/A lb-ft. of torque @ N/A rpm |
| Bore | 4 in (101.6 mm) |
| Stroke | 3 in (76.2 mm) |
| Compression | write compression ratio here |
| In. Valves | in inches |
| Ex. Valves | in inches |
| Firing Order | Firing order of cylinders |
| Left Bank | Write which cylinders are in this bank (write N/A if it it is inline) |
| Right Bank | (same as above) |
| Length | in inches |
| Diameter | in inches |
| Width | in inches |
| Height | in inches |
| Dry Weight | lbs. / kg. |
| Fuel Consumption | city/highway (mpg & km/L) |
| Emission/s | CO: g/km CO2: g/km NOx: g/km Hydrocarbon: g/km Particulate: g/km |
| Chief Engineer | write here |
The Iron Duke (also called the 2500, 151, Pontiac 2.5, Cross Flow, and Tech IV, though the decal on the air filter assemblies actually reads "4 Tech") was a 2.5 L (150.8 cu in) I4 piston engine. All Iron Dukes were built by Pontiac beginning in 1977 and ending in 1993.
This 151 was also used by American Motors (AMC) starting in 1980, as the base engine option in the RWD Spirit and Concord, and continuing in both cars through 1982. The AWD (4x4) Eagle carried the 151 as standard equipment for 1981, and carried it midway through the 1983 model year. It was also available (as the Hurricane) in economy model Jeep CJs. AMC replaced the Iron Duke 2.5L I4 with a 150cid Inline-4 of their own, derived from their evergreen sixes.
The Iron Duke is often confused with Chevrolet's Stovebolt-derived 153 from the 1960s Chevy II, but the engines are entirely different - the Iron Duke's intake manifold is on the passenger side, as opposed to the driver side.
Applications:
- 1977 Pontiac Astre
- 1977-1980 Pontiac Sunbird
- 1984-1988 Pontiac Fiero
- 1982-1985 Pontiac Firebird
- 1982-1985 Chevrolet Camaro
- 1985-1990 Chevrolet Astro
- 1985-1990 GMC Safari
- 1989-1992 Pontiac Grand Prix
- 1978-1980 Oldsmobile Starfire
- Chevrolet Citation
- Chevrolet Celebrity
- Chevrolet S-10
- Chevrolet S-10 Blazer
- GMC Sonoma
- GMC S-15 Jimmy
- Chevrolet Monza
- Buick Skylark
- Buick Skyhawk
- Buick Century
- Pontiac 6000
- 1985-1991 Pontiac Grand Am
- Oldsmobile Ciera
- Oldsmobile Omega
- AMC Concord/Spirit (1980-82)
- Eagle (1981-83)
- Jeep CJ (1980-83)
- Grumman LLV United States Postal Service delivery vehicle
- 1975-1992 Chevrolet Opala (Brazil)
| Year | hp (kW) | ft·lbf (N·m) |
|---|---|---|
| 1978 | 85 (63) | 123 (167) |
| 1979 | 90 (67) | 128 (173) |
| 1980 | 86 (64) | 128 (173) |
LS6
The LS6 was a 151 cu in (2.5 L) I4 engine produced from 1978 to 1979.
LS8
The LS8 was a 151 cu in (2.5 L) I4 engine produced for 1979.
LX6
The LX6 was a 151 cu in (2.5 L) I4 engine produced from 1977 to 1978.
LX8
The LX8 was a 151 cu in (2.5 L) I4 engine produced from 1979 to 1980.
151-S
The 151-S was a 151 cu in (2.5 L) I4 (98 hp) engine produced from 1975 to 1992 for Chevrolet Opala (Brazil).
Crossflow
Cross-flow cylinder heads were added in mid-1979, leading people to refer to this version as the crossflow. Output stood at 90 hp (67 kW).
Tech IV
Iron Dukes were fitted with fuel injection (TBI, via a single injector in the throttle body) in 1982. This version was christened the Tech IV, though Car and Driver later ridiculed it as the low-Tech IV. Power output remained at 90 hp (67 kW).
This was replaced by a swirl-port head with 9.0:1 (instead of 8.2:1) compression ratio in 1984 for a 2 hp (1.5 kW) gain. Other additions for 1985 included roller lifters, improved bearings, and a new crankshaft.
A more-modern serpentine belt and a distributorless ignition system (DIS) was added in 1987, increasing power to 98 hp (73 kW). The engine was updated one final time two years later with balance shafts, new pistons, rods, crankshaft, and an in-pan oiling system. This 1989 Tech IV produced 110 hp (82 kW).
The Tech IV uses the same bellhousing pattern as the 2.8 L 60-Degree V6.
Over the years, the Tech IV engine has proved to be a reliable, if noisy, workhorse for owners when not pushed to its limits. All 1978-1990 Iron Duke L-4's are outfitted with a micarta camshaft gear that meshes directly with a steel gear on the crankshaft (no timing chain). 1991-92 VIN R and U engines received a timing chain. The timing gear has a tendency to crumble a tooth anytime after 80,000 miles. The cam gear simply shears a tooth at startup and the engine won't start. When the cam gear loses a tooth, the camshaft AND distributor stop rotating during engine cranking.
Replacing the gear requires heating the new gear in hot oil and quickly installing it for a press fit on the cam stub.
A few Tech IV owners experience minor driveability issues with the engine. There are several cheap/easy repairs that the shadetree mechanic can perform to keep this engine running at its best.
Inspection (and replacement, if necessary) of the MAP sensor, and its accompanying vacuum hose, is often a solution to many driveability problems. This sensor largely controls the engine's driveability. Stuck EGR valves are also very common on the Tech IV. When replacing the EGR, a mechanic should only use a new, Delphi-sourced or AC Delco part, as aftermarket EGR valves have diaphragm springs that are too weak for this engine. This causes hesitation, sag, stumbling, and sometimes, hard starting. Oxygen sensors should also be replaced every 30,000 miles (48,000 km) on this engine.
Applications:
- 1985-1993 Chevrolet S-10/GMC S-15 Sonoma
- 1985-1990 Chevrolet Astro
- 1990-1992 Chevrolet Lumina
- 1984-1988 Pontiac Fiero
- 1982-1985 Chevrolet Citation II
- 1982-1984 Pontiac Phoenix, Oldsmobile Omega
- 1982-1991 Pontiac 6000, Chevrolet Celebrity, Oldsmobile Cutlass Ciera, Buick Century
- 1985-1991 Pontiac Grand Am, Oldsmobile Cutlass Calais, Buick Somerset, Buick Skylark
- 1982-1986 Pontiac Firebird and Chevrolet Camaro
Racing versions
Though not a production engine, the Super Duty 4 racing engine was notable and widely publicized at the time. It was the basis for NASCAR's Touring Car series. The Super Duty 4 (usually called the "SD4") is still in use today for ARCA Racing.
A 2.7L 232 hp (173 kW) SD4 engine powered the 1984 Fiero Indy Pace Car to over 138 mph during the race. The SD4 was never available in production vehicles, however Pontiac's Performance Parts counter had all the SD4 parts available and one could garner a 2.7L 272 hp (203 kW) version and a 3.2L 330 hp (250 kW) version. All 2000 Indy Fiero replicas came with the 2.5L 92 hp (69 kW) Iron Duke engine.
The SD4 was the last in a line of high performance Pontiac "Super Duty" engines. Kansas Racing Products still makes the engines after buying the rights to make them from GM.
Cosworth also produced a 16-valve head (Cosworth Project DBA, 1987) for the Iron Duke.<ref name="Cosworth Type Reference">Cosworth Type Reference</ref>
